Actions

KitchenAid kbfs25ewms10: Difference between revisions

From Rabbi Blog

← Older edit
VisualWikitext
 
Line 8: Line 8:
==Bottom Drawer==
==Bottom Drawer==
===Removal===
===Removal===
* To remove the bottom drawer on the KBFS25EWMS10, first fully extend the drawer. Locate the release tabs or levers on each side of the drawer slides. Press or lift these tabs simultaneously while gently pulling the drawer out. If it resists, check for any obstructions or debris in the tracks. Clean the tracks if needed and ensure the drawer is level before reinserting. Regular cleaning prevents sticking and prolongs smooth operation.
# Extend the entire drawer
* Video: https://youtu.be/OuqSkMnI-UY?t=25
# Remove inner tray cages
# Unscrew the 2 (one each side) 1/4" screws holding the top inner drawer rail.
#* The top drawer can be extending it to the end of the track and gently pulling it past the rail. Getting it back in will require releasing the two tabs so the gear wheel free floats.
# The front panel sits atop 4 screws: slightly unscrew these (not all the way) and lift the front panel off. (Heavy)
# Center vent cover has a small clip (flat head screwdriver) to assist removal.
# Right side sensor panel has a small clip.
# Ice tray
## Disconnect the power cable (two small clips)
## Slight unscrew the two top screws
## Remove the bottom screw and remove the ice tray
# Back panel has four screws: remove them
# Remove the power connector
# Remove the back panel
===Installing===
# Make sure the sensor is pulled into place when placing the back panel
# Place back panel in place
## Attach the power connector to panel
## Use a screw driver to assist aligning the hose
# Screw in the four screws
# Ice tray
## Hang the tray on the two screw
## Secure the bottom screw
## Secure the top screws
## Align the water hose
## Connect the power
# Thread sensor in sensor guard and attach to back (upper right)
# Attach fan guard
# Place bottom cage back in lower drawer
# Upper rail
## On the upper rail assembly, release the two tabs on each of the gear house
## Insert the upper rail assembly
## Click gear housing into place
# Insert upper cage and ice tray

Latest revision as of 15:53, 25 October 2026


Item: Kitchenaid Refrigerator
Model: KBFS25EWMS10

Bottom Drawer

Removal

  1. Extend the entire drawer
  2. Remove inner tray cages
  3. Unscrew the 2 (one each side) 1/4" screws holding the top inner drawer rail.
    • The top drawer can be extending it to the end of the track and gently pulling it past the rail. Getting it back in will require releasing the two tabs so the gear wheel free floats.
  4. The front panel sits atop 4 screws: slightly unscrew these (not all the way) and lift the front panel off. (Heavy)
  5. Center vent cover has a small clip (flat head screwdriver) to assist removal.
  6. Right side sensor panel has a small clip.
  7. Ice tray
    1. Disconnect the power cable (two small clips)
    2. Slight unscrew the two top screws
    3. Remove the bottom screw and remove the ice tray
  8. Back panel has four screws: remove them
  9. Remove the power connector
  10. Remove the back panel

Installing

  1. Make sure the sensor is pulled into place when placing the back panel
  2. Place back panel in place
    1. Attach the power connector to panel
    2. Use a screw driver to assist aligning the hose
  3. Screw in the four screws
  4. Ice tray
    1. Hang the tray on the two screw
    2. Secure the bottom screw
    3. Secure the top screws
    4. Align the water hose
    5. Connect the power
  5. Thread sensor in sensor guard and attach to back (upper right)
  6. Attach fan guard
  7. Place bottom cage back in lower drawer
  8. Upper rail
    1. On the upper rail assembly, release the two tabs on each of the gear house
    2. Insert the upper rail assembly
    3. Click gear housing into place
  9. Insert upper cage and ice tray
Retrieved from "https://www.rabbibob.com/index.php?title=KitchenAid_kbfs25ewms10&oldid=2078"