Logitech Wireless Headset Cutting Out - Revision history

Rabbi Bob at 22:23, 15 December 2019

2019-12-15T22:23:32Z

← Older revision		Revision as of 22:23, 15 December 2019
Line 1:		Line 1:
	After all that... I think those settings are for equalization		After all that... I think those settings are for equalization

	sigh		sigh

Rabbi Bob at 22:23, 15 December 2019

2019-12-15T22:23:20Z

← Older revision		Revision as of 22:23, 15 December 2019
Line 1:		Line 1:
			After all that... I think those settings are for equalization

			sigh


	Ran into this issue a few years back when we had our 2.4Ghz wireless AP close to the USB receiver for a Logitech G930 headset: the headset would beep and cut out a lot (lose connection). Very inconvenient\annoying\etc. I ended up disabling 2.4 on the AP because I had other ones in the house I could run. This weekend we upgraded the wireless AP and due to what we were doing (getting rid of the old APs), I needed 2.4Ghz to be enabled from the new device.		Ran into this issue a few years back when we had our 2.4Ghz wireless AP close to the USB receiver for a Logitech G930 headset: the headset would beep and cut out a lot (lose connection). Very inconvenient\annoying\etc. I ended up disabling 2.4 on the AP because I had other ones in the house I could run. This weekend we upgraded the wireless AP and due to what we were doing (getting rid of the old APs), I needed 2.4Ghz to be enabled from the new device.

Rabbi Bob: /* Logitech */

2019-12-15T11:38:50Z

Logitech

← Older revision		Revision as of 11:38, 15 December 2019
Line 8:		Line 8:
	=Logitech=		=Logitech=
	* Make sure you are running Logitech drivers (if not, I am not sure where Windows default driver controls this).		* Make sure you are running Logitech drivers (if not, I am not sure where Windows default driver controls this).
			** I am using g930_100364b_x64.exe
	* Set the headset to using channel 1 using Regedit (example below)		* Set the headset to using channel 1 using Regedit (example below)
	<pre>		<pre>

Rabbi Bob at 11:38, 15 December 2019

2019-12-15T11:38:10Z

← Older revision		Revision as of 11:38, 15 December 2019
Line 26:		Line 26:
	</pre>		</pre>

			* Restart Windows

			Note: this is a per user setting in the registry. Multiple profiles will need to have the regkey set.

	[[Category:Windows]]		[[Category:Windows]]
	[[Category:Weblog-2019-12]]		[[Category:Weblog-2019-12]]

Rabbi Bob: Created page with "Ran into this issue a few years back when we had our 2.4Ghz wireless AP close to the USB receiver for a Logitech G930 headset: the headset would beep and cut out a lot (lose c..."

2019-12-15T11:36:51Z

Created page with "Ran into this issue a few years back when we had our 2.4Ghz wireless AP close to the USB receiver for a Logitech G930 headset: the headset would beep and cut out a lot (lose c..."

New page

Ran into this issue a few years back when we had our 2.4Ghz wireless AP close to the USB receiver for a Logitech G930 headset: the headset would beep and cut out a lot (lose connection). Very inconvenient\annoying\etc. I ended up disabling 2.4 on the AP because I had other ones in the house I could run. This weekend we upgraded the wireless AP and due to what we were doing (getting rid of the old APs), I needed 2.4Ghz to be enabled from the new device.

If you have the options to lock in your wireless 2.4Ghz channel, consider the following:

=Wireless AP=
* Lock the 2.4Ghz into a channel. I chose 11 for our house where we only have the 1 AP running. If we put in a second, I'll look at 6 for that one. We should never have a 3rd here. This usually can be done in the admin panel of the device, sometimes under Advanced.

=Logitech=
* Make sure you are running Logitech drivers (if not, I am not sure where Windows default driver controls this).
* Set the headset to using channel 1 using Regedit (example below)
<pre>
Windows Registry Editor Version 5.00

[HKEY_CURRENT_USER\Software\Logitech\G930]
@=""
"Band1GainLevel"=dword:00000001
"Band2GainLevel"=dword:00000000
"Band3GainLevel"=dword:00000000
"Band4GainLevel"=dword:00000000
"Band5GainLevel"=dword:00000000
"Band6GainLevel"=dword:00000000
"Band7GainLevel"=dword:00000000
"Band8GainLevel"=dword:00000000
"Band9GainLevel"=dword:00000000
"Band10GainLevel"=dword:00000000
</pre>

[[Category:Windows]]
[[Category:Weblog-2019-12]]